|
HTML rendering created 2024-06-26 by Michael Kerrisk, author of The Linux Programming Interface. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH. |
|
|
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | COMMANDS | EXAMPLES | CONFIGURATION COOKBOOK | EXIT STATUS | SEE ALSO | COLOPHON |
|
|
|
ovs-vsctl(8) Open vSwitch Manual ovs-vsctl(8)
ovs-vsctl - utility for querying and configuring ovs-vswitchd
ovs-vsctl [options] -- [options] command [args] [-- [options]
command [args]]...
The ovs-vsctl program configures ovs-vswitchd(8) by providing a
high-level interface to its configuration database. See
ovs-vswitchd.conf.db(5) for comprehensive documentation of the
database schema.
ovs-vsctl connects to an ovsdb-server process that maintains an
Open vSwitch configuration database. Using this connection, it
queries and possibly applies changes to the database, depending
on the supplied commands. Then, if it applied any changes, by
default it waits until ovs-vswitchd has finished reconfiguring
itself before it exits. (If you use ovs-vsctl when ovs-vswitchd
is not running, use --no-wait.)
ovs-vsctl can perform any number of commands in a single run,
implemented as a single atomic transaction against the database.
The ovs-vsctl command line begins with global options (see
OPTIONS below for details). The global options are followed by
one or more commands. Each command should begin with -- by
itself as a command-line argument, to separate it from the
following commands. (The -- before the first command is
optional.) The command itself starts with command-specific
options, if any, followed by the command name and any arguments.
See EXAMPLES below for syntax examples.
Linux VLAN Bridging Compatibility
The ovs-vsctl program supports the model of a bridge implemented
by Open vSwitch, in which a single bridge supports ports on
multiple VLANs. In this model, each port on a bridge is either a
trunk port that potentially passes packets tagged with 802.1Q
headers that designate VLANs or it is assigned a single implicit
VLAN that is never tagged with an 802.1Q header.
For compatibility with software designed for the Linux bridge,
ovs-vsctl also supports a model in which traffic associated with
a given 802.1Q VLAN is segregated into a separate bridge. A
special form of the add-br command (see below) creates a ``fake
bridge'' within an Open vSwitch bridge to simulate this behavior.
When such a ``fake bridge'' is active, ovs-vsctl will treat it
much like a bridge separate from its ``parent bridge,'' but the
actual implementation in Open vSwitch uses only a single bridge,
with ports on the fake bridge assigned the implicit VLAN of the
fake bridge of which they are members. (A fake bridge for VLAN 0
receives packets that have no 802.1Q tag or a tag with VLAN 0.)
The following options affect the behavior ovs-vsctl as a whole.
Some individual commands also accept their own options, which are
given just before the command name. If the first command on the
command line has options, then those options must be separated
from the global options by --.
--db=server
Sets server as the database server that ovs-vsctl contacts
to query or modify configuration. server may be an OVSDB
active or passive connection method, as described in
ovsdb(7). The default is
unix:/usr/local/var/run/openvswitch/db.sock.
--no-wait
Prevents ovs-vsctl from waiting for ovs-vswitchd to
reconfigure itself according to the modified database.
This option should be used if ovs-vswitchd is not running;
otherwise, ovs-vsctl will not exit until ovs-vswitchd
starts.
This option has no effect if the commands specified do not
change the database.
--no-syslog
By default, ovs-vsctl logs its arguments and the details
of any changes that it makes to the system log. This
option disables this logging.
This option is equivalent to --verbose=vsctl:syslog:warn.
--oneline
Modifies the output format so that the output for each
command is printed on a single line. New-line characters
that would otherwise separate lines are printed as \n, and
any instances of \ that would otherwise appear in the
output are doubled. Prints a blank line for each command
that has no output. This option does not affect the
formatting of output from the list or find commands; see
Table Formatting Options below.
--dry-run
Prevents ovs-vsctl from actually modifying the database.
-t secs
--timeout=secs
By default, or with a secs of 0, ovs-vsctl waits forever
for a response from the database. This option limits
runtime to approximately secs seconds. If the timeout
expires, ovs-vsctl will exit with a SIGALRM signal. (A
timeout would normally happen only if the database cannot
be contacted, or if the system is overloaded.)
--retry
Without this option, if ovs-vsctl connects outward to the
database server (the default) then ovs-vsctl will try to
connect once and exit with an error if the connection
fails (which usually means that ovsdb-server is not
running).
With this option, or if --db specifies that ovs-vsctl
should listen for an incoming connection from the database
server, then ovs-vsctl will wait for a connection to the
database forever.
Regardless of this setting, --timeout always limits how
long ovs-vsctl will wait.
Table Formatting Options
These options control the format of output from the list and find
commands.
-f format
--format=format
Sets the type of table formatting. The following types of
format are available:
table 2-D text tables with aligned columns.
list (default)
A list with one column per line and rows separated
by a blank line.
html HTML tables.
csv Comma-separated values as defined in RFC 4180.
json JSON format as defined in RFC 4627. The output is
a sequence of JSON objects, each of which
corresponds to one table. Each JSON object has the
following members with the noted values:
caption
The table's caption. This member is omitted
if the table has no caption.
headings
An array with one element per table column.
Each array element is a string giving the
corresponding column's heading.
data An array with one element per table row.
Each element is also an array with one
element per table column. The elements of
this second-level array are the cells that
constitute the table. Cells that represent
OVSDB data or data types are expressed in
the format described in the OVSDB
specification; other cells are simply
expressed as text strings.
-d format
--data=format
Sets the formatting for cells within output tables unless
the table format is set to json, in which case json
formatting is always used when formatting cells. The
following types of format are available:
string (default)
The simple format described in the Database Values
section below.
bare The simple format with punctuation stripped off: []
and {} are omitted around sets, maps, and empty
columns, items within sets and maps are space-
separated, and strings are never quoted. This
format may be easier for scripts to parse.
json The RFC 4627 JSON format as described above.
--no-headings
This option suppresses the heading row that otherwise
appears in the first row of table output.
--pretty
By default, JSON in output is printed as compactly as
possible. This option causes JSON in output to be printed
in a more readable fashion. Members of objects and
elements of arrays are printed one per line, with
indentation.
This option does not affect JSON in tables, which is
always printed compactly.
--bare Equivalent to --format=list --data=bare --no-headings.
--max-column-width=n
For table output only, limits the width of any column in
the output to n columns. Longer cell data is truncated to
fit, as necessary. Columns are always wide enough to
display the column names, if the heading row is printed.
Public Key Infrastructure Options
-p privkey.pem
--private-key=privkey.pem
Specifies a PEM file containing the private key used as
ovs-vsctl's identity for outgoing SSL connections.
-c cert.pem
--certificate=cert.pem
Specifies a PEM file containing a certificate that
certifies the private key specified on -p or --private-key
to be trustworthy. The certificate must be signed by the
certificate authority (CA) that the peer in SSL
connections will use to verify it.
-C cacert.pem
--ca-cert=cacert.pem
Specifies a PEM file containing the CA certificate that
ovs-vsctl should use to verify certificates presented to
it by SSL peers. (This may be the same certificate that
SSL peers use to verify the certificate specified on -c or
--certificate, or it may be a different one, depending on
the PKI design in use.)
-C none
--ca-cert=none
Disables verification of certificates presented by SSL
peers. This introduces a security risk, because it means
that certificates cannot be verified to be those of known
trusted hosts.
--bootstrap-ca-cert=cacert.pem
When cacert.pem exists, this option has the same effect as
-C or --ca-cert. If it does not exist, then ovs-vsctl
will attempt to obtain the CA certificate from the SSL
peer on its first SSL connection and save it to the named
PEM file. If it is successful, it will immediately drop
the connection and reconnect, and from then on all SSL
connections must be authenticated by a certificate signed
by the CA certificate thus obtained.
This option exposes the SSL connection to a man-in-the-
middle attack obtaining the initial CA certificate, but it
may be useful for bootstrapping.
This option is only useful if the SSL peer sends its CA
certificate as part of the SSL certificate chain. The SSL
protocol does not require the server to send the CA
certificate.
This option is mutually exclusive with -C and --ca-cert.
--peer-ca-cert=peer-cacert.pem
Specifies a PEM file that contains one or more additional
certificates to send to SSL peers. peer-cacert.pem should
be the CA certificate used to sign ovs-vsctl's own
certificate, that is, the certificate specified on -c or
--certificate. If ovs-vsctl's certificate is self-signed,
then --certificate and --peer-ca-cert should specify the
same file.
This option is not useful in normal operation, because the
SSL peer must already have the CA certificate for the peer
to have any confidence in ovs-vsctl's identity. However,
this offers a way for a new installation to bootstrap the
CA certificate on its first SSL connection.
-v[spec]
--verbose=[spec]
Sets logging levels. Without any spec, sets the log level
for every module and destination to dbg. Otherwise, spec
is a list of words separated by spaces or commas or
colons, up to one from each category below:
• A valid module name, as displayed by the vlog/list
command on ovs-appctl(8), limits the log level
change to the specified module.
• syslog, console, or file, to limit the log level
change to only to the system log, to the console,
or to a file, respectively. (If --detach is
specified, ovs-vsctl closes its standard file
descriptors, so logging to the console will have no
effect.)
On Windows platform, syslog is accepted as a word
and is only useful along with the --syslog-target
option (the word has no effect otherwise).
• off, emer, err, warn, info, or dbg, to control the
log level. Messages of the given severity or
higher will be logged, and messages of lower
severity will be filtered out. off filters out all
messages. See ovs-appctl(8) for a definition of
each log level.
Case is not significant within spec.
Regardless of the log levels set for file, logging to a
file will not take place unless --log-file is also
specified (see below).
For compatibility with older versions of OVS, any is
accepted as a word but has no effect.
-v
--verbose
Sets the maximum logging verbosity level, equivalent to
--verbose=dbg.
-vPATTERN:destination:pattern
--verbose=PATTERN:destination:pattern
Sets the log pattern for destination to pattern. Refer to
ovs-appctl(8) for a description of the valid syntax for
pattern.
-vFACILITY:facility
--verbose=FACILITY:facility
Sets the RFC5424 facility of the log message. facility can
be one of kern, user, mail, daemon, auth, syslog, lpr,
news, uucp, clock, ftp, ntp, audit, alert, clock2, local0,
local1, local2, local3, local4, local5, local6 or local7.
If this option is not specified, daemon is used as the
default for the local system syslog and local0 is used
while sending a message to the target provided via the
--syslog-target option.
--log-file[=file]
Enables logging to a file. If file is specified, then it
is used as the exact name for the log file. The default
log file name used if file is omitted is
/usr/local/var/log/openvswitch/ovs-vsctl.log.
--syslog-target=host:port
Send syslog messages to UDP port on host, in addition to
the system syslog. The host must be a numerical IP
address, not a hostname.
--syslog-method=method
Specify method how syslog messages should be sent to
syslog daemon. Following forms are supported:
• libc, use libc syslog() function. Downside of
using this options is that libc adds fixed prefix
to every message before it is actually sent to the
syslog daemon over /dev/log UNIX domain socket.
• unix:file, use UNIX domain socket directly. It is
possible to specify arbitrary message format with
this option. However, rsyslogd 8.9 and older
versions use hard coded parser function anyway that
limits UNIX domain socket use. If you want to use
arbitrary message format with older rsyslogd
versions, then use UDP socket to localhost IP
address instead.
• udp:ip:port, use UDP socket. With this method it
is possible to use arbitrary message format also
with older rsyslogd. When sending syslog messages
over UDP socket extra precaution needs to be taken
into account, for example, syslog daemon needs to
be configured to listen on the specified UDP port,
accidental iptables rules could be interfering with
local syslog traffic and there are some security
considerations that apply to UDP sockets, but do
not apply to UNIX domain sockets.
• null, discards all messages logged to syslog.
The default is taken from the OVS_SYSLOG_METHOD
environment variable; if it is unset, the default is libc.
-h
--help Prints a brief help message to the console.
-V
--version
Prints version information to the console.
The commands implemented by ovs-vsctl are described in the
sections below.
Open vSwitch Commands
These commands work with an Open vSwitch as a whole.
init Initializes the Open vSwitch database, if it is empty. If
the database has already been initialized, this command
has no effect.
Any successful ovs-vsctl command automatically initializes
the Open vSwitch database if it is empty. This command is
provided to initialize the database without executing any
other command.
show Prints a brief overview of the database contents.
emer-reset
Reset the configuration into a clean state. It
deconfigures OpenFlow controllers, OVSDB servers, and SSL,
and deletes port mirroring, fail_mode, NetFlow, sFlow, and
IPFIX configuration. This command also removes all
other-config keys from all database records, except that
other-config:hwaddr is preserved if it is present in a
Bridge record. Other networking configuration is left as-
is.
Bridge Commands
These commands examine and manipulate Open vSwitch bridges.
[--may-exist] add-br bridge
Creates a new bridge named bridge. Initially the bridge
will have no ports (other than bridge itself).
Without --may-exist, attempting to create a bridge that
exists is an error. With --may-exist, this command does
nothing if bridge already exists as a real bridge.
[--may-exist] add-br bridge parent vlan
Creates a ``fake bridge'' named bridge within the existing
Open vSwitch bridge parent, which must already exist and
must not itself be a fake bridge. The new fake bridge
will be on 802.1Q VLAN vlan, which must be an integer
between 0 and 4095. The parent bridge must not already
have a fake bridge for vlan. Initially bridge will have
no ports (other than bridge itself).
Without --may-exist, attempting to create a bridge that
exists is an error. With --may-exist, this command does
nothing if bridge already exists as a VLAN bridge under
parent for vlan.
[--if-exists] del-br bridge
Deletes bridge and all of its ports. If bridge is a real
bridge, this command also deletes any fake bridges that
were created with bridge as parent, including all of their
ports.
Without --if-exists, attempting to delete a bridge that
does not exist is an error. With --if-exists, attempting
to delete a bridge that does not exist has no effect.
[--real|--fake] list-br
Lists all existing real and fake bridges on standard
output, one per line. With --real or --fake, only bridges
of that type are returned.
br-exists bridge
Tests whether bridge exists as a real or fake bridge. If
so, ovs-vsctl exits successfully with exit code 0. If
not, ovs-vsctl exits unsuccessfully with exit code 2.
br-to-vlan bridge
If bridge is a fake bridge, prints the bridge's 802.1Q
VLAN as a decimal integer. If bridge is a real bridge,
prints 0.
br-to-parent bridge
If bridge is a fake bridge, prints the name of its parent
bridge. If bridge is a real bridge, print bridge.
br-set-external-id bridge key [value]
Sets or clears an ``external ID'' value on bridge. These
values are intended to identify entities external to Open
vSwitch with which bridge is associated, e.g. the bridge's
identifier in a virtualization management platform. The
Open vSwitch database schema specifies well-known key
values, but key and value are otherwise arbitrary strings.
If value is specified, then key is set to value for
bridge, overwriting any previous value. If value is
omitted, then key is removed from bridge's set of external
IDs (if it was present).
For real bridges, the effect of this command is similar to
that of a set or remove command in the external-ids column
of the Bridge table. For fake bridges, it actually
modifies keys with names prefixed by fake-bridge- in the
Port table.
br-get-external-id bridge [key]
Queries the external IDs on bridge. If key is specified,
the output is the value for that key or the empty string
if key is unset. If key is omitted, the output is
key=value, one per line, for each key-value pair.
For real bridges, the effect of this command is similar to
that of a get command in the external-ids column of the
Bridge table. For fake bridges, it queries keys with
names prefixed by fake-bridge- in the Port table.
Port Commands
These commands examine and manipulate Open vSwitch ports. These
commands treat a bonded port as a single entity.
list-ports bridge
Lists all of the ports within bridge on standard output,
one per line. The local port bridge is not included in
the list.
[--may-exist] add-port bridge port [column[:key]=value]...
Creates on bridge a new port named port from the network
device of the same name.
Optional arguments set values of column in the Port record
created by the command. For example, tag=9 would make the
port an access port for VLAN 9. The syntax is the same as
that for the set command (see Database Commands below).
Without --may-exist, attempting to create a port that
exists is an error. With --may-exist, this command does
nothing if port already exists on bridge and is not a
bonded port.
[--if-exists] del-port [bridge] port
Deletes port. If bridge is omitted, port is removed from
whatever bridge contains it; if bridge is specified, it
must be the real or fake bridge that contains port.
Without --if-exists, attempting to delete a port that does
not exist is an error. With --if-exists, attempting to
delete a port that does not exist has no effect.
[--if-exists] --with-iface del-port [bridge] iface
Deletes the port named iface or that has an interface
named iface. If bridge is omitted, the port is removed
from whatever bridge contains it; if bridge is specified,
it must be the real or fake bridge that contains the port.
Without --if-exists, attempting to delete the port for an
interface that does not exist is an error. With
--if-exists, attempting to delete the port for an
interface that does not exist has no effect.
port-to-br port
Prints the name of the bridge that contains port on
standard output.
Bond Commands
These commands work with ports that have more than one interface,
which Open vSwitch calls ``bonds.''
[--fake-iface] add-bond bridge port iface...
[column[:key]=value]...
Creates on bridge a new port named port that bonds
together the network devices given as each iface. At
least two interfaces must be named. If the interfaces are
DPDK enabled then the transaction will need to include
operations to explicitly set the interface type to 'dpdk'.
Optional arguments set values of column in the Port record
created by the command. The syntax is the same as that
for the set command (see Database Commands below).
With --fake-iface, a fake interface with the name port is
created. This should only be used for compatibility with
legacy software that requires it.
Without --may-exist, attempting to create a port that
exists is an error. With --may-exist, this command does
nothing if port already exists on bridge and bonds
together exactly the specified interfaces.
[--may-exist] add-bond-iface bond iface
Adds iface as a new bond interface to the existing port
bond. If bond previously had only one port, this
transforms it into a bond.
Without --may-exist, attempting to add an iface that is
already part of bond is an error. With --may-exist, this
command does nothing if iface is already part of bond.
(It is still an error if iface is an interface of some
other port or bond.)
[--if-exists] del-bond-iface [bond] iface
Removes iface from its port. If bond is omitted, iface is
removed from whatever port contains it; if bond is
specified, it must be the port that contains bond.
If removing iface causes its port to have only a single
interface, then that port transforms from a bond into an
ordinary port. It is an error if iface is the only
interface in its port.
Without --if-exists, attempting to delete an interface
that does not exist is an error. With --if-exists,
attempting to delete an interface that does not exist has
no effect.
Interface Commands
These commands examine the interfaces attached to an Open vSwitch
bridge. These commands treat a bonded port as a collection of
two or more interfaces, rather than as a single port.
list-ifaces bridge
Lists all of the interfaces within bridge on standard
output, one per line. The local port bridge is not
included in the list.
iface-to-br iface
Prints the name of the bridge that contains iface on
standard output.
Conntrack Zone Commands
These commands query and modify datapath CT zones, Timeout
Policies and Limits.
[--may-exist] add-zone-tp datapath zone=zone_id policies
Creates a conntrack zone timeout policy with zone_id in
datapath. The policies consist of key=value pairs,
separated by spaces. For example, icmp_first=30
icmp_reply=60 specifies a 30-second timeout policy for the
first ICMP packet and a 60-second policy for ICMP reply
packets. See the CT_Timeout_Policy table in
ovs-vswitchd.conf.db(5) for the supported keys.
Without --may-exist, attempting to add a policy for
zone_id that already has a policy is an error.
With --may-exist, this command does nothing if policy for
zone_id already exists.
[--if-exists] del-zone-tp datapath zone=zone_id
Delete the timeout policy associated with zone_id from
datapath.
Without --if-exists, attempting to delete a policy for
zone that does not exist or doesn't have a policy is an
error. With --if-exists, attempting to delete a a policy
that does not exist has no effect.
list-zone-tp datapath
Prints the timeout policies of all zones in datapath.
set-zone-limit datapath zone_id|default zone_limit
Sets a conntrack zone limit with zone_id|default in
datapath. The limit with value 0 means unlimited.
[--if-exists] del-zone-limit datapath zone_id|default
Delete the limit associated with zone_id from datapath.
Without --if-exists, attempting to delete a limit for zone
that does not exist or doesn't have a limit is an error.
With --if-exists, attempting to delete a limit that does
not exist has no effect.
list-zone-limits datapath
Prints the limits of all zones in datapath.
Datapath Capabilities Command
The command query datapath capabilities.
list-dp-cap datapath
Prints the datapath's capabilities.
OpenFlow Controller Connectivity
ovs-vswitchd can perform all configured bridging and switching
locally, or it can be configured to communicate with one or more
external OpenFlow controllers. The switch is typically
configured to connect to a primary controller that takes charge
of the bridge's flow table to implement a network policy. In
addition, the switch can be configured to listen to connections
from service controllers. Service controllers are typically used
for occasional support and maintenance, e.g. with ovs-ofctl.
get-controller bridge
Prints the configured controller target.
del-controller bridge
Deletes the configured controller target.
set-controller bridge target...
Sets the configured controller target or targets. Each
target may use any of the following forms:
ssl:host[:port]
tcp:host[:port]
The specified port on the given host, which can be
expressed either as a DNS name (if built with
unbound library) or an IP address in IPv4 or IPv6
address format. Wrap IPv6 addresses in square
brackets, e.g. tcp:[::1]:6653. On Linux, use
%device to designate a scope for IPv6 link-level
addresses, e.g. tcp:[fe80::1234%eth0]:6653. For
ssl, the --private-key, --certificate, and
--ca-cert options are mandatory.
If port is not specified, it defaults to 6653.
unix:file
On POSIX, a Unix domain server socket named file.
On Windows, connect to a local named pipe that is
represented by a file created in the path file to
mimic the behavior of a Unix domain socket.
pssl:[port][:host]
ptcp:[port][:host]
Listens for OpenFlow connections on port. The
default port is 6653. By default, connections are
allowed from any IPv4 address. Specify host as an
IPv4 address or a bracketed IPv6 address (e.g.
ptcp:6653:[::1]). On Linux, use %device to
designate a scope for IPv6 link-level addresses,
e.g. ptcp:6653:[fe80::1234%eth0]. DNS names can be
used if built with unbound library. For pssl, the
--private-key,--certificate, and --ca-cert options
are mandatory.
punix:file
Listens for OpenFlow connections on the Unix domain
server socket named file.
Controller Failure Settings
When a controller is configured, it is, ordinarily, responsible
for setting up all flows on the switch. Thus, if the connection
to the controller fails, no new network connections can be set
up. If the connection to the controller stays down long enough,
no packets can pass through the switch at all.
If the value is standalone, or if neither of these settings is
set, ovs-vswitchd will take over responsibility for setting up
flows when no message has been received from the controller for
three times the inactivity probe interval. In this mode,
ovs-vswitchd causes the datapath to act like an ordinary MAC-
learning switch. ovs-vswitchd will continue to retry connecting
to the controller in the background and, when the connection
succeeds, it discontinues its standalone behavior.
If this option is set to secure, ovs-vswitchd will not set up
flows on its own when the controller connection fails.
get-fail-mode bridge
Prints the configured failure mode.
del-fail-mode bridge
Deletes the configured failure mode.
set-fail-mode bridge standalone|secure
Sets the configured failure mode.
Manager Connectivity
These commands manipulate the manager_options column in the
Open_vSwitch table and rows in the Managers table. When
ovsdb-server is configured to use the manager_options column for
OVSDB connections (as described in the startup scripts provided
with Open vSwitch; the corresponding ovsdb-server command option
is --remote=db:Open_vSwitch,Open_vSwitch,manager_options), this
allows the administrator to use ovs-vsctl to configure database
connections.
get-manager
Prints the configured manager(s).
del-manager
Deletes the configured manager(s).
set-manager target...
Sets the configured manager target or targets. Each
target may be an OVSDB active or passive connection
method, e.g. pssl:6640, as described in ovsdb(7).
SSL Configuration
When ovs-vswitchd is configured to connect over SSL for
management or controller connectivity, the following parameters
are required:
private-key
Specifies a PEM file containing the private key used as
the virtual switch's identity for SSL connections to the
controller.
certificate
Specifies a PEM file containing a certificate, signed by
the certificate authority (CA) used by the controller and
manager, that certifies the virtual switch's private key,
identifying a trustworthy switch.
ca-cert
Specifies a PEM file containing the CA certificate used to
verify that the virtual switch is connected to a
trustworthy controller.
These files are read only once, at ovs-vswitchd startup time. If
their contents change, ovs-vswitchd must be killed and restarted.
These SSL settings apply to all SSL connections made by the
virtual switch.
get-ssl
Prints the SSL configuration.
del-ssl
Deletes the current SSL configuration.
[--bootstrap] set-ssl private-key certificate ca-cert
Sets the SSL configuration. The --bootstrap option is
described below.
CA Certificate Bootstrap
Ordinarily, all of the files named in the SSL configuration must
exist when ovs-vswitchd starts. However, if the ca-cert file
does not exist and the --bootstrap option is given, then
ovs-vswitchd will attempt to obtain the CA certificate from the
controller on its first SSL connection and save it to the named
PEM file. If it is successful, it will immediately drop the
connection and reconnect, and from then on all SSL connections
must be authenticated by a certificate signed by the CA
certificate thus obtained.
This option exposes the SSL connection to a man-in-the-middle
attack obtaining the initial CA certificate, but it may be useful
for bootstrapping.
This option is only useful if the controller sends its CA
certificate as part of the SSL certificate chain. The SSL
protocol does not require the controller to send the CA
certificate.
Auto-Attach Commands
The IETF Auto-Attach SPBM draft standard describes a compact
method of using IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
together with a IEEE 802.1aq Shortest Path Bridging (SPB) network
to automatically attach network devices to individual services in
a SPB network. The intent here is to allow network applications
and devices using OVS to be able to easily take advantage of
features offered by industry standard SPB networks. A fundamental
element of the Auto-Attach feature is to map traditional VLANs
onto SPB I_SIDs. These commands manage the Auto-Attach I-SID/VLAN
mappings.
add-aa-mapping bridge i-sid vlan
Creates a new Auto-Attach mapping on bridge for i-sid and
vlan.
del-aa-mapping bridge i-sid vlan
Deletes an Auto-Attach mapping on bridge for i-sid and
vlan.
get-aa-mapping bridge
Lists all of the Auto-Attach mappings within bridge on
standard output.
Database Commands
These commands query and modify the contents of ovsdb tables.
They are a slight abstraction of the ovsdb interface and as such
they operate at a lower level than other ovs-vsctl commands.
Identifying Tables, Records, and Columns
Each of these commands has a table parameter to identify a table
within the database. Many of them also take a record parameter
that identifies a particular record within a table. The record
parameter may be the UUID for a record, and many tables offer
additional ways to identify records. Some commands also take
column parameters that identify a particular field within the
records in a table.
For a list of tables and their columns, see
ovs-vswitchd.conf.db(5) or see the table listing from the --help
option.
Record names must be specified in full and with correct
capitalization, except that UUIDs may be abbreviated to their
first 4 (or more) hex digits, as long as that is unique within
the table. Names of tables and columns are not case-sensitive,
and - and _ are treated interchangeably. Unique abbreviations of
table and column names are acceptable, e.g. net or n is
sufficient to identify the NetFlow table.
Database Values
Each column in the database accepts a fixed type of data. The
currently defined basic types, and their representations, are:
integer
A decimal integer in the range -2**63 to 2**63-1,
inclusive.
real A floating-point number.
Boolean
True or false, written true or false, respectively.
string An arbitrary Unicode string, except that null bytes are
not allowed. Quotes are optional for most strings that
begin with an English letter or underscore and consist
only of letters, underscores, hyphens, and periods.
However, true and false and strings that match the syntax
of UUIDs (see below) must be enclosed in double quotes to
distinguish them from other basic types. When double
quotes are used, the syntax is that of strings in JSON,
e.g. backslashes may be used to escape special characters.
The empty string must be represented as a pair of double
quotes ("").
UUID Either a universally unique identifier in the style of RFC
4122, e.g. f81d4fae-7dec-11d0-a765-00a0c91e6bf6, or an
@name defined by a get or create command within the same
ovs-vsctl invocation.
Multiple values in a single column may be separated by spaces or
a single comma. When multiple values are present, duplicates are
not allowed, and order is not important. Conversely, some
database columns can have an empty set of values, represented as
[], and square brackets may optionally enclose other non-empty
sets or single values as well. For a column accepting a set of
integers, database commands accept a range. A range is
represented by two integers separated by -. A range is inclusive.
A range has a maximum size of 4096 elements. If more elements are
needed, they can be specified in separate ranges.
A few database columns are ``maps'' of key-value pairs, where the
key and the value are each some fixed database type. These are
specified in the form key=value, where key and value follow the
syntax for the column's key type and value type, respectively.
When multiple pairs are present (separated by spaces or a comma),
duplicate keys are not allowed, and again the order is not
important. Duplicate values are allowed. An empty map is
represented as {}. Curly braces may optionally enclose non-empty
maps as well (but use quotes to prevent the shell from expanding
other-config={0=x,1=y} into other-config=0=x other-config=1=y,
which may not have the desired effect).
Database Command Syntax
[--if-exists] [--columns=column[,column]...] list table
[record]...
Lists the data in each specified record. If no records
are specified, lists all the records in table.
If --columns is specified, only the requested columns are
listed, in the specified order. Otherwise, all columns
are listed, in alphabetical order by column name.
Without --if-exists, it is an error if any specified
record does not exist. With --if-exists, the command
ignores any record that does not exist, without producing
any output.
[--columns=column[,column]...] find table [column[:key]=value]...
Lists the data in each record in table whose column equals
value or, if key is specified, whose column contains a key
with the specified value. The following operators may be
used where = is written in the syntax summary:
= != < > <= >=
Selects records in which column[:key] equals, does
not equal, is less than, is greater than, is less
than or equal to, or is greater than or equal to
value, respectively.
Consider column[:key] and value as sets of
elements. Identical sets are considered equal.
Otherwise, if the sets have different numbers of
elements, then the set with more elements is
considered to be larger. Otherwise, consider a
element from each set pairwise, in increasing order
within each set. The first pair that differs
determines the result. (For a column that contains
key-value pairs, first all the keys are compared,
and values are considered only if the two sets
contain identical keys.)
{=} {!=}
Test for set equality or inequality, respectively.
{<=} Selects records in which column[:key] is a subset
of value. For example, flood-vlans{<=}1,2 selects
records in which the flood-vlans column is the
empty set or contains 1 or 2 or both.
{<} Selects records in which column[:key] is a proper
subset of value. For example, flood-vlans{<}1,2
selects records in which the flood-vlans column is
the empty set or contains 1 or 2 but not both.
{>=} {>}
Same as {<=} and {<}, respectively, except that the
relationship is reversed. For example, flood-
vlans{>=}1,2 selects records in which the flood-
vlans column contains both 1 and 2.
The following operators are available only in Open vSwitch
2.16 and later:
{in} Selects records in which every element in
column[:key] is also in value. (This is the same
as {<=}.)
{not-in}
Selects records in which every element in
column[:key] is not in value.
For arithmetic operators (= != < > <= >=), when key is
specified but a particular record's column does not
contain key, the record is always omitted from the
results. Thus, the condition other-config:mtu!=1500
matches records that have a mtu key whose value is not
1500, but not those that lack an mtu key.
For the set operators, when key is specified but a
particular record's column does not contain key, the
comparison is done against an empty set. Thus, the
condition other-config:mtu{!=}1500 matches records that
have a mtu key whose value is not 1500 and those that lack
an mtu key.
Don't forget to escape < or > from interpretation by the
shell.
If --columns is specified, only the requested columns are
listed, in the specified order. Otherwise all columns are
listed, in alphabetical order by column name.
The UUIDs shown for rows created in the same ovs-vsctl
invocation will be wrong.
[--if-exists] [--id=@name] get table record [column[:key]]...
Prints the value of each specified column in the given
record in table. For map columns, a key may optionally be
specified, in which case the value associated with key in
the column is printed, instead of the entire map.
Without --if-exists, it is an error if record does not
exist or key is specified, if key does not exist in
record. With --if-exists, a missing record yields no
output and a missing key prints a blank line.
If @name is specified, then the UUID for record may be
referred to by that name later in the same ovs-vsctl
invocation in contexts where a UUID is expected.
Both --id and the column arguments are optional, but
usually at least one or the other should be specified. If
both are omitted, then get has no effect except to verify
that record exists in table.
--id and --if-exists cannot be used together.
[--if-exists] set table record column[:key]=value...
Sets the value of each specified column in the given
record in table to value. For map columns, a key may
optionally be specified, in which case the value
associated with key in that column is changed (or added,
if none exists), instead of the entire map.
Without --if-exists, it is an error if record does not
exist. With --if-exists, this command does nothing if
record does not exist.
[--if-exists] add table record column [key=]value...
Adds the specified value or key-value pair to column in
record in table. If column is a map, then key is
required, otherwise it is prohibited. If key already
exists in a map column, then the current value is not
replaced (use the set command to replace an existing
value).
Without --if-exists, it is an error if record does not
exist. With --if-exists, this command does nothing if
record does not exist.
[--if-exists] remove table record column value...
[--if-exists] remove table record column key...
[--if-exists] remove table record column key=value...
Removes the specified values or key-value pairs from
column in record in table. The first form applies to
columns that are not maps: each specified value is removed
from the column. The second and third forms apply to map
columns: if only a key is specified, then any key-value
pair with the given key is removed, regardless of its
value; if a value is given then a pair is removed only if
both key and value match.
It is not an error if the column does not contain the
specified key or value or pair.
Without --if-exists, it is an error if record does not
exist. With --if-exists, this command does nothing if
record does not exist.
[--if-exists] clear table record column...
Sets each column in record in table to the empty set or
empty map, as appropriate. This command applies only to
columns that are allowed to be empty.
Without --if-exists, it is an error if record does not
exist. With --if-exists, this command does nothing if
record does not exist.
[--id=(@name | uuid] create table column[:key]=value...
Creates a new record in table and sets the initial values
of each column. Columns not explicitly set will receive
their default values. Outputs the UUID of the new row.
If @name is specified, then the UUID for the new row may
be referred to by that name elsewhere in the same
ovs-vsctl invocation in contexts where a UUID is expected.
Such references may precede or follow the create command.
If a valid uuid is specified, then it is used as the UUID
of the new row.
Caution (ovs-vsctl as example)
Records in the Open vSwitch database are
significant only when they can be reached directly
or indirectly from the Open_vSwitch table. Except
for records in the QoS or Queue tables, records
that are not reachable from the Open_vSwitch table
are automatically deleted from the database. This
deletion happens immediately, without waiting for
additional ovs-vsctl commands or other database
activity. Thus, a create command must generally be
accompanied by additional commands within the same
ovs-vsctl invocation to add a chain of references
to the newly created record from the top-level
Open_vSwitch record. The EXAMPLES section gives
some examples that show how to do this.
[--if-exists] destroy table record...
Deletes each specified record from table. Unless
--if-exists is specified, each records must exist.
--all destroy table
Deletes all records from the table.
Caution (ovs-vsctl as example)
The destroy command is only useful for records in
the QoS or Queue tables. Records in other tables
are automatically deleted from the database when
they become unreachable from the Open_vSwitch
table. This means that deleting the last reference
to a record is sufficient for deleting the record
itself. For records in these tables, destroy is
silently ignored. See the EXAMPLES section below
for more information.
wait-until table record [column[:key]=value]...
Waits until table contains a record named record whose
column equals value or, if key is specified, whose column
contains a key with the specified value. This command
supports the same operators and semantics described for
the find command above.
If no column[:key]=value arguments are given, this command
waits only until record exists. If more than one such
argument is given, the command waits until all of them are
satisfied.
Caution (ovs-vsctl as example)
Usually wait-until should be placed at the
beginning of a set of ovs-vsctl commands. For
example, wait-until bridge br0 -- get bridge br0
datapath_id waits until a bridge named br0 is
created, then prints its datapath_id column,
whereas get bridge br0 datapath_id -- wait-until
bridge br0 will abort if no bridge named br0 exists
when ovs-vsctl initially connects to the database.
Consider specifying --timeout=0 along with --wait-until,
to prevent ovs-vsctl from terminating after waiting only
at most 5 seconds.
comment [arg]...
This command has no effect on behavior, but any database
log record created by the command will include the command
and its arguments.
Create a new bridge named br0 and add port eth0 to it:
ovs-vsctl add-br br0
ovs-vsctl add-port br0 eth0
Alternatively, perform both operations in a single atomic
transaction:
ovs-vsctl add-br br0 -- add-port br0 eth0
Delete bridge br0, reporting an error if it does not exist:
ovs-vsctl del-br br0
Delete bridge br0 if it exists:
ovs-vsctl --if-exists del-br br0
Set the qos column of the Port record for eth0 to point to a new
QoS record, which in turn points with its queue 0 to a new Queue
record:
ovs-vsctl -- set port eth0 qos=@newqos -- --id=@newqos
create qos type=linux-htb other-config:max-rate=1000000
queues:0=@newqueue -- --id=@newqueue create queue
other-config:min-rate=1000000
other-config:max-rate=1000000
Port Configuration
Add an ``internal port'' vlan10 to bridge br0 as a VLAN access
port for VLAN 10, and configure it with an IP address:
ovs-vsctl add-port br0 vlan10 tag=10 -- set Interface
vlan10 type=internal
ip addr add 192.168.0.123/24 dev vlan10
Add a GRE tunnel port gre0 to remote IP address 1.2.3.4 to bridge
br0:
ovs-vsctl add-port br0 gre0 -- set Interface gre0 type=gre
options:remote_ip=1.2.3.4
Port Mirroring
Mirror all packets received or sent on eth0 or eth1 onto eth2,
assuming that all of those ports exist on bridge br0 (as a side-
effect this causes any packets received on eth2 to be ignored):
ovs-vsctl -- set Bridge br0 mirrors=@m \
-- --id=@eth0 get Port eth0 \
-- --id=@eth1 get Port eth1 \
-- --id=@eth2 get Port eth2 \
-- --id=@m create Mirror name=mymirror select-dst-
port=@eth0,@eth1 select-src-port=@eth0,@eth1 output-
port=@eth2
Remove the mirror created above from br0, which also destroys the
Mirror record (since it is now unreferenced):
ovs-vsctl -- --id=@rec get Mirror mymirror \
-- remove Bridge br0 mirrors @rec
The following simpler command also works:
ovs-vsctl clear Bridge br0 mirrors
Quality of Service (QoS)
Create a linux-htb QoS record that points to a few queues and use
it on eth0 and eth1:
ovs-vsctl -- set Port eth0 qos=@newqos \
-- set Port eth1 qos=@newqos \
-- --id=@newqos create QoS type=linux-htb
other-config:max-rate=1000000000 queues=0=@q0,1=@q1 \
-- --id=@q0 create Queue other-config:min-rate=100000000
other-config:max-rate=100000000 \
-- --id=@q1 create Queue other-config:min-rate=500000000
Deconfigure the QoS record above from eth1 only:
ovs-vsctl clear Port eth1 qos
To deconfigure the QoS record from both eth0 and eth1 and then
delete the QoS record (which must be done explicitly because
unreferenced QoS records are not automatically destroyed):
ovs-vsctl -- destroy QoS eth0 -- clear Port eth0 qos --
clear Port eth1 qos
(This command will leave two unreferenced Queue records in the
database. To delete them, use "ovs-vsctl list Queue" to find
their UUIDs, then "ovs-vsctl destroy Queue uuid1 uuid2" to
destroy each of them or use "ovs-vsctl -- --all destroy Queue" to
delete all records.)
Connectivity Monitoring
Monitor connectivity to a remote maintenance point on eth0.
ovs-vsctl set Interface eth0 cfm_mpid=1
Deconfigure connectivity monitoring from above:
ovs-vsctl clear Interface eth0 cfm_mpid
NetFlow
Configure bridge br0 to send NetFlow records to UDP port 5566 on
host 192.168.0.34, with an active timeout of 30 seconds:
ovs-vsctl -- set Bridge br0 netflow=@nf \
-- --id=@nf create NetFlow targets=\"192.168.0.34:5566\"
active-timeout=30
Update the NetFlow configuration created by the previous command
to instead use an active timeout of 60 seconds:
ovs-vsctl set NetFlow br0 active_timeout=60
Deconfigure the NetFlow settings from br0, which also destroys
the NetFlow record (since it is now unreferenced):
ovs-vsctl clear Bridge br0 netflow
sFlow
Configure bridge br0 to send sFlow records to a collector on
10.0.0.1 at port 6343, using eth1's IP address as the source,
with specific sampling parameters:
ovs-vsctl -- --id=@s create sFlow agent=eth1
target=\"10.0.0.1:6343\" header=128 sampling=64 polling=10
\
-- set Bridge br0 sflow=@s
Deconfigure sFlow from br0, which also destroys the sFlow record
(since it is now unreferenced):
ovs-vsctl -- clear Bridge br0 sflow
IPFIX
Configure bridge br0 to send one IPFIX flow record per packet
sample to UDP port 4739 on host 192.168.0.34, with Observation
Domain ID 123 and Observation Point ID 456, a flow cache active
timeout of 1 minute (60 seconds), maximum flow cache size of 13
flows, and flows sampled on output port with tunnel info(sampling
on input and output port is enabled by default if not disabled) :
ovs-vsctl -- set Bridge br0 ipfix=@i \
-- --id=@i create IPFIX targets=\"192.168.0.34:4739\"
obs_domain_id=123 obs_point_id=456 cache_active_timeout=60
cache_max_flows=13 \
other_config:enable-input-sampling=false
other_config:enable-tunnel-sampling=true
Deconfigure the IPFIX settings from br0, which also destroys the
IPFIX record (since it is now unreferenced):
ovs-vsctl clear Bridge br0 ipfix
802.1D Spanning Tree Protocol (STP)
Configure bridge br0 to participate in an 802.1D spanning tree:
ovs-vsctl set Bridge br0 stp_enable=true
Set the bridge priority of br0 to 0x7800:
ovs-vsctl set Bridge br0 other_config:stp-priority=0x7800
Set the path cost of port eth0 to 10:
ovs-vsctl set Port eth0 other_config:stp-path-cost=10
Deconfigure STP from above:
ovs-vsctl set Bridge br0 stp_enable=false
Multicast Snooping
Configure bridge br0 to enable multicast snooping:
ovs-vsctl set Bridge br0 mcast_snooping_enable=true
Set the multicast snooping aging time br0 to 300 seconds:
ovs-vsctl set Bridge br0 other_config:mcast-snooping-
aging-time=300
Set the multicast snooping table size br0 to 2048 entries:
ovs-vsctl set Bridge br0 other_config:mcast-snooping-
table-size=2048
Disable flooding of unregistered multicast packets to all ports.
When set to true, the switch will send unregistered multicast
packets only to ports connected to multicast routers. When it is
set to false, the switch will send them to all ports. This
command disables the flood of unregistered packets on bridge br0.
ovs-vsctl set Bridge br0 other_config:mcast-snooping-
disable-flood-unregistered=true
Enable flooding of multicast packets (except Reports) on a
specific port.
ovs-vsctl set Port eth1 other_config:mcast-snooping-
flood=true
Enable flooding of Reports on a specific port.
ovs-vsctl set Port eth1 other_config:mcast-snooping-flood-
reports=true
Deconfigure multicasting snooping from above:
ovs-vsctl set Bridge br0 mcast_snooping_enable=false
802.1D-2004 Rapid Spanning Tree Protocol (RSTP)
Configure bridge br0 to participate in an 802.1D-2004 Rapid
Spanning Tree:
ovs-vsctl set Bridge br0 rstp_enable=true
Set the bridge address of br0 to 00:aa:aa:aa:aa:aa :
ovs-vsctl set Bridge br0 other_config:rstp-
address=00:aa:aa:aa:aa:aa
Set the bridge priority of br0 to 0x7000. The value must be
specified in decimal notation and should be a multiple of 4096
(if not, it is rounded down to the nearest multiple of 4096). The
default priority value is 0x800 (32768).
ovs-vsctl set Bridge br0 other_config:rstp-priority=28672
Set the bridge ageing time of br0 to 1000 s. The ageing time
value should be between 10 s and 1000000 s. The default value is
300 s.
ovs-vsctl set Bridge br0 other_config:rstp-ageing-
time=1000
Set the bridge force protocol version of br0 to 0. The force
protocol version has two acceptable values: 0 (STP compatibility
mode) and 2 (normal operation).
ovs-vsctl set Bridge br0 other_config:rstp-force-protocol-
version=0
Set the bridge max age of br0 to 10 s. The max age value should
be between 6 s and 40 s. The default value is 20 s.
ovs-vsctl set Bridge br0 other_config:rstp-max-age=10
Set the bridge forward delay of br0 to 15 s. This value should
be between 4 s and 30 s. The default value is 15 s.
ovs-vsctl set Bridge br0 other_config:rstp-forward-
delay=15
Set the bridge transmit hold count of br0 to 7 s. This value
should be between 1 s and 10 s. The default value is 6 s.
ovs-vsctl set Bridge br0 other_config:rstp-transmit-hold-
count=7
Enable RSTP on the Port eth0:
ovs-vsctl set Port eth0 other_config:rstp-enable=true
Disable RSTP on the Port eth0:
ovs-vsctl set Port eth0 other_config:rstp-enable=false
Set the priority of port eth0 to 32. The value must be specified
in decimal notation and should be a multiple of 16 (if not, it is
rounded down to the nearest multiple of 16). The default priority
value is 0x80 (128).
ovs-vsctl set Port eth0 other_config:rstp-port-priority=32
Set the port number of port eth0 to 3:
ovs-vsctl set Port eth0 other_config:rstp-port-num=3
Set the path cost of port eth0 to 150:
ovs-vsctl set Port eth0 other_config:rstp-path-cost=150
Set the admin edge value of port eth0:
ovs-vsctl set Port eth0 other_config:rstp-port-admin-
edge=true
Set the auto edge value of port eth0:
ovs-vsctl set Port eth0 other_config:rstp-port-auto-
edge=true
Set the admin point to point MAC value of port eth0. Acceptable
values are 0 (not point-to-point), 1 (point-to-point, the default
value) or 2 (automatic detection). The auto-detection mode is
not currently implemented, and the value 2 has the same effect of
0 (not point-to-point).
ovs-vsctl set Port eth0 other_config:rstp-admin-p2p-mac=1
Set the admin port state value of port eth0. true is the default
value.
ovs-vsctl set Port eth0 other_config:rstp-admin-port-
state=false
Set the mcheck value of port eth0:
ovs-vsctl set Port eth0 other_config:rstp-port-mcheck=true
Deconfigure RSTP from above:
ovs-vsctl set Bridge br0 rstp_enable=false
OpenFlow Version
Configure bridge br0 to support OpenFlow versions 1.0, 1.2, and
1.3:
ovs-vsctl set bridge br0
protocols=OpenFlow10,OpenFlow12,OpenFlow13
Flow Table Configuration
Make flow table 0 on bridge br0 refuse to accept more than 100
flows:
ovs-vsctl -- --id=@ft create Flow_Table flow_limit=100
overflow_policy=refuse -- set Bridge br0 flow_tables=0=@ft
Make flow table 0 on bridge br0 evict flows, with fairness based
on the matched ingress port, when there are more than 100:
ovs-vsctl -- --id=@ft create Flow_Table flow_limit=100
overflow_policy=evict groups='"NXM_OF_IN_PORT[]"' -- set
Bridge br0 flow_tables:0=@ft
0 Successful program execution.
1 Usage, syntax, or configuration file error.
2 The bridge argument to br-exists specified the name of a
bridge that does not exist.
ovsdb-server(1), ovs-vswitchd(8), ovs-vswitchd.conf.db(5).
This page is part of the Open vSwitch (a distributed virtual
multilayer switch) project. Information about the project can be
found at ⟨http://openvswitch.org/⟩. If you have a bug report for
this manual page, send it to bugs@openvswitch.org. This page was
obtained from the project's upstream Git repository
⟨https://github.com/openvswitch/ovs.git⟩ on 2024-06-14. (At that
time, the date of the most recent commit that was found in the
repository was 2024-06-07.) If you discover any rendering
problems in this HTML version of the page, or you believe there
is a better or more up-to-date source for the page, or you have
corrections or improvements to the information in this COLOPHON
(which is not part of the original manual page), send a mail to
man-pages@man7.org
Open vSwitch 3.2.90 ovs-vsctl(8)
Pages that refer to this page: ovsdb-client(1), network_namespaces(7), ovn-architecture(7), ovsdb(7), ovn-ic-nbctl(8), ovn-ic-sbctl(8), ovn-nbctl(8), ovn-sbctl(8), ovs-dpctl(8), ovs-l3ping(8), ovs-test(8), ovs-vlan-test(8), ovs-vswitchd(8), vtep-ctl(8)
|
HTML rendering created 2024-06-26 by Michael Kerrisk, author of The Linux Programming Interface. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH. |
|