ovs-l3ping(8) — Linux manual page

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | EXAMPLES | SEE ALSO | AUTHOR | COPYRIGHT | COLOPHON

OVS-L3PING(8)                 Open vSwitch                 OVS-L3PING(8)

NAME         top

       ovs-l3ping - check network deployment for L3 tunneling problems

SYNOPSIS         top

       ovs-l3ping -s <TunnelRemoteIP>,<InnerIP>[/<mask>] -t <tunnelmode>

       ovs-l3ping -s <TunnelRemoteIP>,<InnerIP>[/<mask>][:<ControlPort>]
       -t <tunnelmode>

       ovs-l3ping -c <TunnelRemoteIP>,<InnerIP>[/<mask>],<RemoteInnerIP>
       -t <tunnelmode>

       ovs-l3ping -c
       <TunnelRemoteIP>,<InnerIP>[/<mask>][:<ControlPort>[:<DataPort>]],<RemoteInnerIP>[:<ControlPort>[:<DataPort>]]
       [-b <targetbandwidth>] [-i <testinterval>] -t <tunnelmode>

       ovs-l3ping -h | --help

       ovs-l3ping -V | --version

DESCRIPTION         top

       The ovs-l3ping program may be used to check for problems that
       could be caused by invalid routing policy, misconfigured firewall
       in the tunnel path or a bad NIC driver.  On one of the nodes, run
       ovs-l3ping in server mode and on the other node run it in client
       mode.  The client and server will establish L3 tunnel, over which
       client will give further testing instructions. The ovs-l3ping
       client will perform UDP and TCP tests.  This tool is different
       from ovs-test that it encapsulates XML/RPC control connection
       over the tunnel, so there is no need to open special holes in
       firewall.

       UDP tests can report packet loss and achieved bandwidth for
       various datagram sizes. By default target bandwidth for UDP tests
       is 1Mbit/s.

       TCP tests report only achieved bandwidth, because kernel TCP
       stack takes care of flow control and packet loss.

   Client Mode
       An ovs-l3ping client will create a L3 tunnel and connect over it
       to the ovs-l3ping server to schedule the tests.  <TunnelRemoteIP>
       is the peer’s IP address, where tunnel will be terminated.
       <InnerIP> is the address that will be temporarily assigned during
       testing.  All test traffic originating from this IP address to
       the <RemoteInnerIP> will be tunneled.  It is possible to override
       default <ControlPort> and <DataPort>, if there is any other
       application that already listens on those two ports.

   Server Mode
       To conduct tests, ovs-l3ping server must be running.  It is
       required that both client and server <InnerIP> addresses are in
       the same subnet.  It is possible to specify <InnerIP> with
       netmask in CIDR format.

OPTIONS         top

       One of -s or -c is required.  The -t option is also required.

       • -s <TunnelRemoteIP>,<InnerIP>[/<mask>][:<ControlPort>] or
         --server <TunnelRemoteIP>,<InnerIP>[/<mask>][:<ControlPort>]

         Run in server mode and create L3 tunnel with the client that
         will be accepting tunnel at <TunnelRemoteIP> address.  The
         socket on <InnerIP>[:<ControlPort>] will be used to receive
         further instructions from the client.

       • -c
         <TunnelRemoteIP>,<InnerIP>[/<mask>][:<ControlPort>[:<DataPort>]],<RemoteInnerIP>[:<ControlPort>[:<DataPort>]]
         or --client
         <TunnelRemoteIP>,<InnerIP>[/<mask>][:<ControlPort>[:<DataPort>]],<RemoteInnerIP>[:<ControlPort>[:<DataPort>]]

         Run in client mode and create L3 tunnel with the server on
         <TunnelRemoteIP>.  The client will use <InnerIP> to generate
         test traffic with the server’s <RemoteInnerIP>.

       • -b <targetbandwidth> or --bandwidth <targetbandwidth>

         Target bandwidth for UDP tests. The <targetbandwidth> must be
         given in bits per second.  Use postfix M or K to alter the
         target bandwidth magnitude.

       • -i <testinterval> or --interval <testinterval>

         How long each test should run. By default 5 seconds.

       • -t <tunnelmode> or --tunnel-mode <tunnelmode>

         Specify the tunnel type. This option must match on server and
         client.

       • -h or --help

         Prints a brief help message to the console.

       • -V or --version

         Prints version information to the console.

EXAMPLES         top

       On host 192.168.122.220 start ovs-l3ping in server mode.  This
       command will create a temporary GRE tunnel with the host
       192.168.122.236 and assign 10.1.1.1/28 as the inner IP address,
       where client will have to connect:

          ovs-l3ping -s 192.168.122.236,10.1.1.1/28 -t gre

       On host 192.168.122.236 start ovs-l3ping in client mode.  This
       command will use 10.1.1.2/28 as the local inner IP address and
       will connect over the L3 tunnel to the server’s inner IP address
       at 10.1.1.1:

          ovs-l3ping -c 192.168.122.220,10.1.1.2/28,10.1.1.1 -t gre

SEE ALSO         top

       ovs-vswitchd(8), ovs-ofctl(8), ovs-vsctl(8), ovs-vlan-test(8),
       ovs-test(8), ethtool(8), uname(1).

AUTHOR         top

       The Open vSwitch Development Community

COPYRIGHT         top

       2016-2021, The Open vSwitch Development Community

COLOPHON         top

       This page is part of the Open vSwitch (a distributed virtual
       multilayer switch) project.  Information about the project can be
       found at ⟨http://openvswitch.org/⟩.  If you have a bug report for
       this manual page, send it to bugs@openvswitch.org.  This page was
       obtained from the project's upstream Git repository
       ⟨https://github.com/openvswitch/ovs.git⟩ on 2023-12-22.  (At that
       time, the date of the most recent commit that was found in the
       repository was 2023-12-21.)  If you discover any rendering
       problems in this HTML version of the page, or you believe there
       is a better or more up-to-date source for the page, or you have
       corrections or improvements to the information in this COLOPHON
       (which is not part of the original manual page), send a mail to
       man-pages@man7.org

3.2.90                        Dec 22, 2023                 OVS-L3PING(8)